LG BA850 Instrukcja Użytkownika

Owner's ManualModel BA850P/N: 4100376500 Rev. A www.lg.com LCD Projector

10Table of ContentsSafety Instructions 2Licenses 9Table of Contents 10Statement 11Part names and functions 12Front 12Back 12Bottom 12Rear termina

11StatementNote:• The screen menu and pictures in the manual may slightly differ from the real product.• The manual is subject to change without prio

12Part names and functionsFrontBackBottom⑦④⑨ ⑩⑪⑥② ①⑤ ③⑧⑬⑭⑭⑫⑮ ⑮①Lens release button②Indicator③Lamp cover④Lens cap⑤Projector lens⑥Decorative cover⑦Remot

13Part names and functionsRear terminalRGB IN 1RGB IN 2RGB OUTVIDEO/YPb/CbPr/CrRS-232CWired R/C① Network port Used to connect the network cable.②

14Part names and functionsSide control and indicatorsSide control Indicator (Top panel)① OK button - Enter menu. - Execute the selected item.

15Part names and functionsRemote control①②*④⑤⑨⑧⑪⑭⑮⑱⑲③⑥ ⑦⑩⑫⑯⑳⑰⑬①POWER button Turn the projector on or off.② COMPONENT button Select the component

16Part names and functions⑰ RATIO button Select a screen display mode.⑱ KEYSTONE button Calibrate keystone distortion.⑲OK button Access the m

17Part names and functionsRemote control battery installationOperation rangeAdjustable feet1. Open the battery compartment lid.2. Install new batte

18InstallationPositioning the projector√ Note: ● The brightness in the room has a great inuence on picture quality. It is recommended to limit the

19InstallationConnecting to computer (Digital and analog RGB)Cables used for connection ( *Cables are not supplied with the projector.)RGB cable (1)

2 Caution: The exclamation point within an equilateral triangle is intended to alert the user to the presence of i

20InstallationConnecting to video equipment (Video, S-Video,Component, HDMI)Cables used for connection (*Cables are not supplied with the projector.)V

21InstallationConnecting to the AC power cordThis projector uses nominal input voltages of 100–240 V AC and it automatically selects the correct input

22InstallationLens installationFollow the instructions below to install the lens upon replacing or using the provided lens. For the specication of pr

23Basic operationTurning on the projector1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector.2 C

24Basic operationTurning off the projector1 Press the POWER button on the side control or on the remote control, and “Power off? Please pres

25Basic operationHow to operate the on screen menuThe projector can be adjusted or set via the on-screen menu.Each main menu can be divided into sever

26Basic operationMenu barRGB2 InputMain menuSub menu①②③④⑤⑥⑦⑧① PC adjust menu Used to ad

27Basic operationAuto setup functionThis function is available just by pressing the AUTO button on the side control or on the remote control. The syst

28Basic operationKeystoneIf a projected picture has keystone distortion, correct the image with the Keystone function.Press the KEYSTONE button on the

29Basic operationRemote control operationUsing the remote control for some frequently used operations is advisable. Just pressing one of the buttons e

3POWERSafety Instructions• The earth wire should be connected.- Inappropriate earth grounding may cause damage to the projector or an electric sho

30Basic operationTIMER buttonPICTURE buttonRATIO buttonMENU buttonSHIFT buttonZOOM buttonFOCUS buttonINFO buttonAUTO buttonPATTERN buttonSLEEP button

31Computer inputInput source select (RGB1)Direct operation- Press the INPUT button on the side control.- Press the RGB1 button on the remote control.R

32Input source select(RGB 2 or RGBHV)Direct operation- Press the INPUT button on the side control.- Press the RGB2 IN or RGBHV button on the remote

33Computer system selectComputer inputThe projector automatically tunes to various types of computers with its function of Multi-scan system and Auto

34Computer inputAuto PC adjustmentAuto PC Adjustment function is provided to automatically adjust phase, total dots, H position, V position to confor

35Computer inputManual adjustment via PCAs some computer adopt special signal formats, the multi-purpose scanner of the projector may not detect them.

36Computer inputImage selectDirect selectionUse the PICTURE button on the remote control to select the image mode.Remote controlPICTURE buttonDynamicW

37Image adjustComputer input1. Press Menu on the remote control to display the on-screen menu. Press ▲▼ to select the image adjust icon .Then pr

38Computer inputScreen size adjustThe size of the screen can be reset to the value the user desires.1. Press Menu on the remote control to display

39Video InputSelecting input source (HDMI/Component/S-Video/Video)Direct selection- Press HDMI, COMPONENT, S-VIDEO or VIDEO button on the remote con

4Safety Instructions• Hold the plug rmly when unplugging.- A broken wire in the cord may cause a re.• Ensure the power cord or plug is not damag

40Video system select1. Press MENU on the remote control to display the on-screen menu. Press ▲▼ to select the icon for input source. Then pres

41Video InputImage selectDirect selectionPress the PICTURE button on the remote control to select the image mode.Menu selection1. Press MENU button

42Video InputImage adjust1. Press MENU button on the remote control to display the on-screen menu. Press ▲▼ to select the image adjust ic

43Video InputScreen size adjustThe size of the screen can be reset to the value the user desires.1.Press MENU button on the remote control to displ

44OptionOptionYou can use the option menu to congure thefollowing functions.1. Press MENU button on the remote control to display the on screen m

45OptionInput searchThis function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to se

46DisplayOptionYou can use this item to set whether the startup animation is displayed.On ...Show startup screen.Off ...

47Enter a Logo PIN codeUse the Point ▲▼ buttons to enter a number. Press the Point ► button to x the number and move the red frame pointer to the nex

48OptionCeilingRearTerminalPower managementPower managementThis function is used to project the image from a ceiling mounted projector.Off ...Disab

49OptionStandby modeClosed CaptionLamp ModeTest PatternSecurity (Key lock and PIN code lock)This function is available when operating the projector vi

5Safety Instructions• When the lamp is on or has just been turned off, avoid touching the air vent or lamp because these will be very hot.• If t

50OptionPIN code lockThis function prevents the projector from being operated by unauthorized persons and provides the following setting options for

51OptionCooling fastThere are the following options in the cooling fans operation when the projector is turned off.ON ... Faster and louder-sound than

52InformationDisplaying input sourceThe information menu is used to detect signal of projected image and running state.Direct operationPress INFO. but

53MaintenanceWARNING TEMP indicatorThe WARNING TEMP indicator tells in what protection state engaged. The user should check the WARNING TEMP indicato

54MaintenanceCleaning the lterThe lter prevents dust from accumulating on the surface of lens assembly. Should the lter become clogged with dust pa

55Covering the lens properlyIf the set needs to be moved or won’t be used forextended period of time, you should cover the lensproperly.Cleaning the l

56MaintenanceReplacing the lampWhen the service life of the projection lamp is over, the icon suggests that the lamp needed to be replaced will appear

57MaintenanceORDER REPLACEMENT LAMPReplacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following informati

58AppendixTroubleshootingBefore calling your dealer or service center for assistance, check the items below once again.- Make sure you have properly c

59Failure SolutionsAuto PC adjust doesn't work. - Check the signal of input source. Automatic adjustment th

6Safety InstructionsCleaning OthersWARNING WARNINGCAUTION• Only a qualied technician can disassemble or modify the projector. For inspection,

60AppendixIndicator and projector stateCheck the indicator to know about the state of projector.IndicatorState of projectorPOWER(Green/Red)WARNING(Red

61AppendixCompatible signalBasically this projector can accept the signal with the V-,H-Frequency mentioned below:√ Note: The specication is subj

62AppendixConguration of terminalsRGB 1/RGB 2/RGB OUT (analog)Terminal: Analog RGB (D-sub 15-pin)51234109 67815141311121 Red (Input/output) 9 -----2

63AppendixTechnical SpecicationsMechanical properties Dimensions (W×H×D ) 534.5 mm x 398.5mm x 193.4mm (without lens) Net Weight 10.8kg Adjustbale

64Appendix● The aforesaid specication is subject to change without prior notice.● Liquid crystal panel is made on the basis of high standard, where 9

65AppendixDimensionsUnit: mm3 0 01 5 02 3 85 81 0534.5193.4176.9146380 5.398 5.465 1.LCD PROJECTORLENS RELEASE114Screw hole used when installed on the

66AppendixContent of hazardous substances and elementsName of partsHazardous substances and elementsPb Hg Cd Cr6+ PBB PBDEBodyPlastic parts ○ ○ ○ ○ ○

67AppendixRS232 Control MethodNOTE: Connect the PC & projector with serial port cable (female-to-female pins) for projector computer co

68Appendix2. CommandsCase sensitive, each command end by[CR](Carriage). The time out for each command is one second. If you want to cancel the time

69Appendix2.4 RGB 12.5 RGB 22.6 Component2.7 Video2.8 S-Video2.9 RGB 2:InputCommand “A05”[CR] (Hex:0x41 0x30 0x35 0x0d)Details Change the input to &qu

7Safety Instructions • Warning - Class B (b) For a Class B Digital device or peripheral, the instructions furnished the user shall includ

70Appendix2.12Keystone ↓2.15 Auto PC Adjust2.13 Menu on2.14 Menu off2.16 Input mode read2.17 Auto setupCommand “A8F”[CR] (Hex:0x41 0x38 0x46 0x0d)Deta

71Appendix2.19 Still off2.20 Blank on2.21 Blank off2.22 Timer2.23 Lamp mode normal2.24 Lamp mode ecoCommand “A44”[CR] (Hex:0x41 0x34 0x34 0x0d)Details

72Appendix2.27 16:92.28 4:32.29 Normal2.30 Custom2.31 Dynamic2.32 Standard (Image select)2.33 CinemaCommand “AW SCREEN WIDE”[CR](Hex: 0x41 0x57 0x20 0

73Appendix2.35 Navigation ►2.36 Navigation ◄2.37 Navigation ▲2.38 Navigation ▼2.39 Select2.40 HDMICommand “A3A”[CR] (Hex:0x41 0x33 0x41 0x0d)Details ►

74Appendix2.41 RGBHV2.42 Lamp mode autoCommand “A37”[CR] (Hex:0x41 0x33 0x37 0x0d)Details Change the input to "RGBHV"Return OK "-"

75AppendixLAN controlPreparation:1. Equipments: PC, projector, cables2. Connection procedures:Connect the projector to routers or switches of the LAN

76Appendix5. Network Setting with DHCP "Off" Set DHCP to Off: Assign an IP address manually. Set IP Address as the IP Address for

77AppendixWeb page Operation :1. Check IP address: Enter network menu and select network information. Press select to check IP address.2. Enter the

78Appendix3) Screen: Adjust the screen aspect ratio.4) Image : Preset Image mode can be selected.5) ImageAdj : Contrast and Brightness Values can be a

79Appendix6) Input: Select the input source.7) Option: Select other setting status.<Note>• Information on this page needs to be updated every ti

8Safety Instructions1. When this crossed-out wheeled bin symbol is attached to batteries/ accumulators of Your product it means they are c

www.lg.comThe model and serial number of the projector islocated on the back or bottom side of the projector.Record it below should you ever need serv

9LicensesSupported licenses may differ by model. For more information about licenses, visitwww.lg.com.HDMI, the HDMI logo and High-Denition Multimedi